So I broke a key off into my garage door and I can't seem to get it out and don't have 300$ to pay a locksmith what should I do?

Clef et passeport à l' intérieur . Impossible de l' ouvrir quand j'ai essayé d'insérer la clef de la voiture avec la quelle je démarre la clé n' est pas rentrer en entier et a refusé de sortir ou de bouger . Je suis vraiment embarrassé si quelque un a une solution qui me permettrai de l' ouvrir sans rien casser je suis preneur . Je voudrais l' ouvrir proprement.

Hi,
I have a multipoint lock on my wooden French door, after a party last week I found that someone snapped the handle. The lock mechanism still works and I purchased a replacement handle. The new handle has protruding screw fixings, whereas the old handle was flat. Is this normal or are you supposed to drill into the door to allow the handle to sit flush? This was an expensive handle and I’ve rechecked the description and diagram on their website and it doesn’t give any information about the protruding screw sockets! It’s an oak door so I don’t think that you can tighten the screws sufficiently to embed them into the door.

This isn’t a normal lock. Some old
Manf from 30 years ago. You can’t put a paper clip in the hole to get the thumbturn off. It seems to come off in one piece. I have 5 of them in the house. Please help.

Again you cannot put in a paper clip or anything to remove the thumb turn twist

I have an old Mac toolbox that I restored and the lock stopped working. The key just continuously spins the cylinder with no resistance. I took the cylinder out to inspect and a few tiny brass colored spring flew across the room. The thing basically just fell apart as I pulled it out. This is from the late 1970's early 1980's. How this lock works is the tail end of the cylinder has female threads in it where a kickstand-style rod attaches. When the key is turned, the rod rotates and pushes up on this bar in the back of the toolbox that releases these hooks that keep the drawers locked. Is this a specialty kind of lock or are these pretty common? Where can I get a replacement if the toolbox manufacturer no longer carries this lock?

All the doors lock and unlock when I use the buttons on the key fob.

However, when I try to unlock or lock the driver's door using the button on the door handle, it doesn't work. All the other doors can unlock and lock using the button on the door handle.

Is this simply a bad button that can be fixed by replacing the door handle or could the button be fine but whatever it controls not be working?

Hi! I accidentally pressed this plunger lock on my cabinet drawers. I have no key. My local locksmith was puzzled as there was no marking on the face aside from the "YALE". He had suggested using a very small flathead screwdriver or sharpend point rod to try to use friction to move the piece inside the hole. Do you concur or have any advice? (This is my file cabinet that I inherited with my home in North Richland, Washington. The file cabinet is originally from Hanford and given to my great uncle. It contains only some of my personal files and receipts. I am a 23 yr. veteran of my local fire department. I would like to preserve this antique without having to drill it out.) Thanks in advance!

Hi everyone, looking for some advice on what to do with a lock for the door for our conservatory. During last winter when it wad very cold the door lock was ridiculously stiff to lock and unlock it, required quite a bit of pressure on the handle when lifting it up to unlock it, otherwise it wouldn't unlock when cold.

During warmer/hot weather it's been fine. I understand about expansion and contraction etc but even though it's not getting silly cold overnight we're now facing the same issues with it being ridiculously tight and I fear when it is winter we won't be able to lock it at all, and this is our back door so need it secure.

Not sure what I need to do to fix it, whether it's the case that the cylinder needs replacing or something else to solve the matter. Didn't know if WD40 would help loosen it to make it easier to lock? I dunno really looking for advice.

The lock is a euro cylinder and I have looked up how to replace it if needed and it seems reasonably straight forward enough if I do need to replace it.

Can someone explain a fix for this loose thumb turn on our brand new Yale lock? I don't think the thumb turn should pull away like this.

So I was gifted a fully paid Pontiac g6 (2006) for graduation. My only question so far is my key fob, it only ever worked when locking the door, figured it was the battery, went through 2 batteries and still had the same problem. Is it the car itself? Or is it a faulty key fob?

\- I have a spare fob with the same issue but it only unlocked the car, and fiddled with the alarm.

The gap on the outside is due to the safety plate. When they installed this should they have cut to fit? He assured me over and over that it would be fine. Is this something I need to fight to get fixed or will some silicone caulking be appropriate?

I’m trying to find a replacement driver torsion spring for an Abus 81/45 padlock. I was having some problems with mine and when I took it apart, I found that part of the spring broke off (see photo).

I’ve called my local locksmiths and no one sells parts - just new padlocks. I also checked the Abus (US) website and they don’t have those springs available. To be honest, I can’t find a lot of resources for Abus Series 81 locks.

Thanks in advance for any info.

Hey all I was hoping to get some help on my mul t lock.

I was trying to lock my door the other day and noticed that my key didn’t seem to be going all the way in. When I tried to turn it to lock the door, it was stuck and I couldn’t turn it. When I manually engaged the deadbolt from the inside of the house, the key can turn fine the other way to unlock it.

As soon as I took the lock off, a small ball bearing fell out - I think it fell out from the outside part of the lock.

Based on this Reddit thread, the ball bearing seems to be part of a re-key system.

I think the ball bearing falling out is what's causing the issue. Is it possible to fix this? if so how? Would this be completely outside of the scope for a non professional to deal with ?

Any help is greatly appreciated !

what is the most economical choice for one that doesn’t vin lock after 1 use?

I'm trying to access the metal wafers inside to recode this new lock to work with my existing keys.

Hard to find any information on how to do so.

Any suggestions?

EDIT: Pics in comments

I went for a 2 day trip with family and when i returned back i found this jammed in my lock. It’s a very basic 6 lever padlock. Its works fine after i removed this metal thing out of it.
I have a lot of questions running in my mind.
Was someone really trying to pick the lock?
Can the lock be picked with this piece of metal?
Should I replace the lock?
What can I do to improve the security?

This lock is an extra safety measure as the iron door also has an inbuilt lock and the wooden door behind it is also double locked.

Does anyone know how to change the code on this keypad to my front gate?

Got a vintage cupboard (with all my clothes in) that the key has just broken off inside. Any suggestions on being able to open it?

I've tried running a credit card along the door but no movement.