I'm wanting to load some 6.5 cm out of my 24 inch 1/8T proof research carbon sendero as followed (153.5 LRHT, Lapua srp brass, CCI 450 srmp, and h4350). I have emailed berger before about using hornady brass and large rifle primers, but im unsure about this load. I emailed them, but haven't gotten anything back yet.

Any recommendations on how to get this shell out?

Edit: It's out! Thanks everyone!

Got it set up for 9mm and 357 magnum. Still need to get the shotshell press mounted.

I know it's pretty niche, but I'm just looking for any experience that might be out there. I currently use 79g of H1000, and it works quite well (3069fps/SD<8/24"). I'm just experimenting with a new powder option.

Sierra lists an N570 Load of 75.2-82.0 with a lead HPBT. That's all I have to go on at this point.

I also see a forum discussion with a guy who took N570 all the way to 88.5g with a berger 200.2. He reports no pressure signs and the pic of his brass looked absolutely fine. But his speed from a 20" barrel was in the 2800's. That doesn't compute to me. Maybe that slow powder and short barrel was just blowing it all out the business end.

I'm going to load up 20 rounds and go look for trouble and see what I can find. In the absence of other data, I think I'll load up 74.5-84.0 (.5g steps) and see what happens.

Lapua SRP brass, h4350, Remington 7 1/2 br primers. Looking for around 2750 mv. Won't be able to take them out for another 2 weeks. Anticipation is killing me.

Did some well needed rearranging on my powder bench. Happy with it now!

I postponed downloading it. And now it's no longer available. Or is it?

Anyone have a link? An alternative?

Recently bought a Redding X10 competition powder measure to replace my Lee deluxe perfect powder measure. I like using the Lee, but I wanted a powder measure with a continuous adjustment knob and more consistency. However to my dismay the $250 Redding is performing worse than the $70 Lee. Not only was it more difficult to setup and use, but it was less precise than the Lee. I tried following the instruction manual and fully disassembling and cleaning it but it did not help. Has anyone else had this experience? Could my unit be defective or is there something I’m overlooking?

I can’t find this anywhere. I am trying to do that second recipe on the 1oz list. I can’t find the felt or the wad. ChatGPT said they don’t make it anymore and was replaced with something else. Can anyone share some links, I’m so tired of looking for this.

What sources do you use? Is there a place where the information is consolidated?

I have an AT4 paired with an FX120i scale and for the most part I like the device. That said, the scale drifts sometimes between charges by .01 or .002 grain, and definitely when left alone overnight. EDIT: this is a typo, meant .02

On the between charges, I recognize this could be due to a stray kernel or two making it to the platen, and my understanding is that the scale (or maybe AT?) automatically rezeros the device if it’s within some small tolerance? If this is true does this have any impact on my load consistency, or does the automatic rezero take care of that?

Secondly, I leave my scale on 24/7, and have occasionally put a 75 grain projectile on there to see if I am holding my measurement, and it’s not. The projectile weights 74.96 and if I leave it on there for days it can wander up and down from 74.88 to 75.08. This is not that reassuring for a scale that is supposed to be accurate to .02, but I always re-zero before use and given the above question, I don’t think it actually matters when it comes to the scale’s performance, but I’m not positive.

Curious to hear people’s thoughts. I do have some ferrite rings on the power cable but it does not seem to do anything. Next step is probably a dedicated ground wire, and maybe a line conditioner, but hard to justify a couple hundred extra dollars if none of this really matters due to scale rezeroing anyway during loading.

I just picked up my first press. My plan is to buy primed cases from Shell Shock Technologies and load them to use for hunting.

My question for anyone with experience with these cases, do I need to size or trim them? Or can I just fill them with powder and load a bullet and go?

Do I need any special or specific dies to load this ammo?

For anyone with experience loading these in 308, id like to push a 150-168 grain all copper out of my 20" barrel around 3,000 fps. Is this possible? What powders should I look into?

I'm wanting to pick up a Forester co ax, does anyone know of any Labor Day sales?

guess I finally have an excuse to buy that ergonomic roller handle I've been eyeing for years

anyone have problems with them? The sent the first package and FedEx delivered it to God knows where. I had to wait. Then they sent the second which got sent back to them. They don't seem interested in getting these bullets to me. They just for outcomes from these mistakes.

I’ve loaded up some of what I was assuming to be a large lot of once fired brass that I inherited. It seemed to be in good condition and was cleaned and had the crimps removed, I still ran them through my Dillon to trim and size them before wet tumbling and loading. I actually processed this brass a few years ago so don’t remember the exact process I used.

All of these loaded on a Dillon 650, Cases were primed with Remington 7 1/2 primers and 25 grains of BLC-2 with Xtreme 55 grain bullets loaded to 2.20” and shot from a Daniel Defense 16” AR15 at about 2850 FPS average.

During shooting a while back I had some excessive smoke coming from the ejection port and carbon or powder burn on the rounds in the magazine. I looked for the case but unfortunately was not able to locate anything due to where I was shooting.

Fast forward to now, I was shooting these again and had the same thing happen and I was able to locate the fired case. I finished off my last magazine and had a failure to eject and the case was stuck in the ejection port and I discovered the case in the last two pictures.

I use this rifle in multi-gun competition twice a month and have shot thousands and thousands of rounds through it over the years I’ve had it. I have probably unknowingly experienced this a few more times with these exact reloads and same headstamps, but never had it happen with any factory ammo.

Am I looking at a headspace issue? Is this bad brass? I don’t see any pressure signs on the other fired cases that would cause me to worry. Or could this be an issue with processing/sizing? I adjusted my trim/sizing die to where the case drops right into a case gauge so I can fire it from any rifle I have.

I'm new to reloading and have only reloaded blue bullets. For some odd reason, one delivery went somewhere else and another went back to them.

Are there any similar bullets I could which would not require any changes or if so, few changes to reloading?

The old reloads of my (now deceased) grandfather that we found in his gunlocker

He did not own a press, so we do not know exactly how he pressed the bullets in there

We do not know exactly what kind of powder he used, or how much he used (we found multiple cans)

We do not know the different bullets grains

These will never be fired😂

So...

I'm still very much impressed with this press.

I only use it for reloading pistol cartridges so for those of you wondering about loading short action rifle cartridges, I don't have anything for you here unfortunately

First things first: this press LOVES round nose bullets. It loads them like a fucking champion and i have zero complaints.

What i struggled with (mightily) was hollow points.

I went with Barry's hybrid hollow points to give this old girl a chance. Let's just say that it didn't start off well and along the way, things that make this press vulnerable were exposed.

After spending some $ at Armanov to get some upgrades for the press, things started to improve but...

I was still getting non-concentric rounds that wouldn't pass my case gauge (granted: i use the Hornady case gauge which is notoriously tight, but I've been using it for years on stuff loaded from the Dillon 550 and they always pass).

So i started thinking about the tilting at the bullet drop/seater. I tried enlarging the bullet seater void to hit on the ogive of the bullet rather than the tip. This helped, marginally

Then it hit me: before i moved to the X-10, I was using a D.A.A. seater/crimper so I could use a powder check on the dillon.

Knowing this seater does a great job already, i decided to use the bullet dropper as a dropper only and set the integral seater at just enough seat to start the bullet into the brass.

This now puts a started bullet into the next station where it seats and crimps like a dream

The last piece of this puzzle is at the belling station (I bell at the primer station).

Because the bell doesn't allow the bullet to necessarily sit perfectly flat on the brass, I decided to install a Redding Premium Special Expander Die. This creates a perfect channel for the bullet to drop into perfectly straight.

Once i figured these little tricks out, 100% of my cartridges pass the Hornady Gauge and they look amazing to boot.

I'm still not a fan of taking three scews out to dump powder when I'm done, but I cannot complain about the accuracy of the powder drops from the included dropper. I did replace the o-ring with the thicker version and it holds the charge just fine.

And finally: the Lee Undersizing Die is the absolute key to this press IMO. Running this die after the universal decapper has vastly improved the final products.

I wish the bullet shuttle was easier to change out for longer bullet sizes but I've got it figured out at least.

All in all, I'm still definitely a fan of this press.

It took some time to get to know her but once she's dialed in, it's too easy and running 300 rounds in 20 minutes or so.

That kind of production just isn't something i ever thought I'd have at my disposal

So I use lemishine and dawn no ss pins and use a oven at 200 degrees, after drying 9mm I noticed that some cases look like it has a wax residue any idea what’s causing this?